Nokia 1110-1600 lcd light solution
Tuesday, December 14, 2010
Specifications Blackberry 9800 Torch
Specifications Blackberry 9800 Torch
* 3.2-inch touchscreen display* 480 x 360 resolution
* A full, slide-out QWERTY keyboard
* Optical trackpad
* 5-megapixel autofocus camera with video and scenes
* BlackBerry OS 6 with integrated search and new UI
* BlackBerry Enterprise Servicer, the BlackBerry Internet Service, Mobile Instant Messaging
* Bluetooth 2.1 with A2DP
* Wi-Fi 802.11b/g/n with AT & T Hot Spots support
* 512MB of RAM and 512 MB Flash
* 4GB of Flash memory and a 4GB microSD card
* UMTS: 2100/1900/850/800 MHz (bands 1,2,5 / 6)
* GSM / GPRS / EDGE: 850/900/1800/1900
* Full HTML browser tabbed
* Social networking support for Facebook, MySpace and Twitter
* Music and video playing support including iTunes sync
* 1.300 mAh Lithium battery
Tips to Improve Phone Damage
THIS Tips to Improve Phone Damage - Although a bit busy, I am taking the time to menulis.maklum hp blower .. as carpenters, rainy season like this much hp in pain, some sick with a fever, flu, there is also very ill, to enter the emergency room , tp certainly not enter the emergency room at rmh pain cipto are pretty, but in the emergency room where repair hp .. hehehe.namanya clinic also hp, hp jd all tried at tackle disease, for hp td healthy again ..
Today I want to share a little about the tricks to improve cell phone, for those of you who want to deepen knowledge about the mob, or who want to become a technician alias hp hp blower, hopefully this trick is useful for you ..
As I mentioned in my previous post, that the mob was divided into two elements, namely elements of software and hardware, so here I review again the damage to the hp, but with the solution ..
Damage Software
--------------------------------------------------------------------------------------------------------------
The things that often occurs due to damage to software:
1. Hang (the keypad buttons do not work)
2. Blank / white screen appears only
3. Total death caused by a virus or error using the application
4. Phonelock
5. Contact Service
6. Phone restricted
7. Unable to boot
8. Simcard not accepted / rejected sim card / sim rejected / incorrect sim card
9. Unable to signal
10. Contact retailer
11. Restart
12. Contact the provider (for SE)
13. Wrong Software (for Siemens)
--------------------------------------------------------------------------------------------------------------
The things that often happen due to hardware damage:
1. Total death
2. Signal
3. Voice disorder
4. Charging battery
5. Display screen (LCD)
6. UI (user interface)
7. Lighting (LED)
8. Vibrator (Shakes)
9. Buzer (ringtones)
---------------------------------------------------------------------------------------------------------------
Solutions By Hardware Dead
Dead cell phone there are several categories:The cause of the damage characteristic solutiondead mobile phone, while making a call. However, when normal life standby phone. Flow transmitter circuit is too large. Ø Check the battery, when it is dropped it must diganti.Ø Replace IC PA (Power Amplyfier)dead cell phone, but do not last long (about a couple of minutes straight off) Power supply circuit currents are too large. Ø Replace the IC power supply.dead cell phone, but when the phone can charge battery charge. Series Power up / power down does not work properly. Ø Replace Switch on / off.Ø Jumper when the track to switch on / off drop.total dead cell phone. Ø battery.Ø Input voltage of power supply output voltage at 13mhz Clock Ø Ø Jumper directly from the battery connector to the power input voltage power IC supply.Ø supply.Ø CHANGE CHANGE Proccesor RF ICs.SignalDisturbance signal there are several categories:The cause of the damage characteristic solutionsignal up and down, sometimes even hilang.signal not exist, searchable manualpun not get the network. Ø Strengthening the receiver (LNA) is not sempurna.Ø System duplexer (antenna switching). Ø LNA on nokia DCT4 and WD2 been combined with IC RF Procesor (Helga / Mjoiner), if damaged replace swith ganti.Ø Antennano signal, when manually searched all networks can, but if at select an operator can not be meregistrtasikan. Ø receiver system is not functioning properly. Ø LNA on nokia DCT4 and WD2 been combined with IC RF Procesor (Helga / Mjoiner), if damaged replace.signal suddenly disappears after 3 seconds. when searched manually to all operators but if the choose not to register their network. Ø System Transmitter is not functioning sempurna.Ø modulation system is not perfect. Ø Replace IC PA (Power Amplyfier). Ø Replace IC RF processor.Voice disorderThere is noise there are several categories:Voice your opponent can not be heard. Ø Speaker System berfungsi.Ø no audio amplifier is not functioning Ø Replace Speaker.Ø Replace the audio IC. Audio system on nokia DCT4/WD2 contained in IC UEMsound can not be sent to mobile opponent. Ø Microphone System berfungsiØ no audio amplifier is not functioning Ø Replace microphoneØ Replace the audio IC. Audio system on nokia DCT4/WD2 contained in IC UEMCharging batterybattery charging problems there are several categories:when in charge transformer connected, the phone can not detect at all (no response) Ø charge voltage of the transformer does not go to the charging control system. Ø Check the fuse, betuk components such as resistors, you can look at the scheme diagram.Ø When the track is good, replace the IC control charging.charge when connected transformers, mobile phones detect the filling, but a few seconds appear the words "Not charging" on the LCD screen. Ø charging voltage of the transformer does not meet the standards of the Charging Control in trouble filling battery.Ø Ø passive components contained in the input circuit of the charging control, replace if there is a Change Control charging bermasalah.Øtrofo charge when connected, the phone can detect and fill in but if pulled back on the phone display reads "redial charging." Ø Control of the CPU does not go to control charging. Ø Jumper. You can see the collection of jumpers that we provide.Display screen (LCD)LCD disorders there are several categories:LCD screens do not display information output from the CPU Ø Command to the LCD. Ø Replace LCDLCD screen LCD problematic partly missing Ø Ø Replace LCDUI (user interface)Lighting (LED) LED Ø rusakØ voltage to the LED does not masukØ command from the CPU does not enter. Ø Replace Replace Ledo Jumper.Ø UI driversVibrator (Shakes) Ø rusakØ Vibrator Vibrator Voltage to masukØ no command from the CPU does not enter. Ø Replace BuzerØ Jumper.Ganti UI driversBuzer (ringtones) Ø Buzer rusakØ Voltage to Buzer not masukØPerintah from the CPU does not enter. Ø Replace Replace BuzerØ Jumper.Ø UI drivers
---------------------------------------------------------------------------------------------------------------
Today I want to share a little about the tricks to improve cell phone, for those of you who want to deepen knowledge about the mob, or who want to become a technician alias hp hp blower, hopefully this trick is useful for you ..
As I mentioned in my previous post, that the mob was divided into two elements, namely elements of software and hardware, so here I review again the damage to the hp, but with the solution ..
Damage Software
--------------------------------------------------------------------------------------------------------------
The things that often occurs due to damage to software:
1. Hang (the keypad buttons do not work)
2. Blank / white screen appears only
3. Total death caused by a virus or error using the application
4. Phonelock
5. Contact Service
6. Phone restricted
7. Unable to boot
8. Simcard not accepted / rejected sim card / sim rejected / incorrect sim card
9. Unable to signal
10. Contact retailer
11. Restart
12. Contact the provider (for SE)
13. Wrong Software (for Siemens)
--------------------------------------------------------------------------------------------------------------
Hardware Damage
The things that often happen due to hardware damage:
1. Total death
2. Signal
3. Voice disorder
4. Charging battery
5. Display screen (LCD)
6. UI (user interface)
7. Lighting (LED)
8. Vibrator (Shakes)
9. Buzer (ringtones)
---------------------------------------------------------------------------------------------------------------
Solutions By Hardware Dead
Dead cell phone there are several categories:The cause of the damage characteristic solutiondead mobile phone, while making a call. However, when normal life standby phone. Flow transmitter circuit is too large. Ø Check the battery, when it is dropped it must diganti.Ø Replace IC PA (Power Amplyfier)dead cell phone, but do not last long (about a couple of minutes straight off) Power supply circuit currents are too large. Ø Replace the IC power supply.dead cell phone, but when the phone can charge battery charge. Series Power up / power down does not work properly. Ø Replace Switch on / off.Ø Jumper when the track to switch on / off drop.total dead cell phone. Ø battery.Ø Input voltage of power supply output voltage at 13mhz Clock Ø Ø Jumper directly from the battery connector to the power input voltage power IC supply.Ø supply.Ø CHANGE CHANGE Proccesor RF ICs.SignalDisturbance signal there are several categories:The cause of the damage characteristic solutionsignal up and down, sometimes even hilang.signal not exist, searchable manualpun not get the network. Ø Strengthening the receiver (LNA) is not sempurna.Ø System duplexer (antenna switching). Ø LNA on nokia DCT4 and WD2 been combined with IC RF Procesor (Helga / Mjoiner), if damaged replace swith ganti.Ø Antennano signal, when manually searched all networks can, but if at select an operator can not be meregistrtasikan. Ø receiver system is not functioning properly. Ø LNA on nokia DCT4 and WD2 been combined with IC RF Procesor (Helga / Mjoiner), if damaged replace.signal suddenly disappears after 3 seconds. when searched manually to all operators but if the choose not to register their network. Ø System Transmitter is not functioning sempurna.Ø modulation system is not perfect. Ø Replace IC PA (Power Amplyfier). Ø Replace IC RF processor.Voice disorderThere is noise there are several categories:Voice your opponent can not be heard. Ø Speaker System berfungsi.Ø no audio amplifier is not functioning Ø Replace Speaker.Ø Replace the audio IC. Audio system on nokia DCT4/WD2 contained in IC UEMsound can not be sent to mobile opponent. Ø Microphone System berfungsiØ no audio amplifier is not functioning Ø Replace microphoneØ Replace the audio IC. Audio system on nokia DCT4/WD2 contained in IC UEMCharging batterybattery charging problems there are several categories:when in charge transformer connected, the phone can not detect at all (no response) Ø charge voltage of the transformer does not go to the charging control system. Ø Check the fuse, betuk components such as resistors, you can look at the scheme diagram.Ø When the track is good, replace the IC control charging.charge when connected transformers, mobile phones detect the filling, but a few seconds appear the words "Not charging" on the LCD screen. Ø charging voltage of the transformer does not meet the standards of the Charging Control in trouble filling battery.Ø Ø passive components contained in the input circuit of the charging control, replace if there is a Change Control charging bermasalah.Øtrofo charge when connected, the phone can detect and fill in but if pulled back on the phone display reads "redial charging." Ø Control of the CPU does not go to control charging. Ø Jumper. You can see the collection of jumpers that we provide.Display screen (LCD)LCD disorders there are several categories:LCD screens do not display information output from the CPU Ø Command to the LCD. Ø Replace LCDLCD screen LCD problematic partly missing Ø Ø Replace LCDUI (user interface)Lighting (LED) LED Ø rusakØ voltage to the LED does not masukØ command from the CPU does not enter. Ø Replace Replace Ledo Jumper.Ø UI driversVibrator (Shakes) Ø rusakØ Vibrator Vibrator Voltage to masukØ no command from the CPU does not enter. Ø Replace BuzerØ Jumper.Ganti UI driversBuzer (ringtones) Ø Buzer rusakØ Voltage to Buzer not masukØPerintah from the CPU does not enter. Ø Replace Replace BuzerØ Jumper.Ø UI drivers
---------------------------------------------------------------------------------------------------------------
Good luck,,,,
Tips and Triks Repair mobile
Whatever your choice do the following:
1. If you get a defective phone service familiarize kroscek complaint with the owner, and make sure the points of damage and hp condition when received, especially if the mob is still alive. Because service and customer trust are key in this field, believe de loss little time but indirectly you've put an invaluable promotion.
2. If possible, the casing and bateray on hand to customers, to avoid confused over the place, because it is often also the incident of his customers do not recognize bateray if later dropped. Minimal label attached to the inside of the casing and bateray if left, and give mobile service bill with a number corresponding label number.
3. Tidy up your service desk, do not get used to work in a cluttered environment with many mobile jakarta dormant on it. Prepare only what it needs to work at that time.
4. Make sure the damage once again with further checks and stacking strategy handphone jakarta repair or service you would do. So do not rush heats az component let alone unpack. Because there are many tricks jumper or alternative solutions that you can choose. Even worse if steps memblower and unloading components that you do on the basis of trial and error.
5. If hp is not in a state short hence it is better to use a check box cell phone service jakarta to determine the appropriate corrective measures. Most hp damage also come from software problems. And damage to software can be overcome by flashing in full or in part.
6. In exploring hardware damage handphone jakarta do the systematic and sequential, and most importantly use the book in every step of the checking line. If you do a sequential and systematic way then you will find a damaged component appropriately and minimize mistakes.
7. Prepare yourself ... that is the most important
1. If you get a defective phone service familiarize kroscek complaint with the owner, and make sure the points of damage and hp condition when received, especially if the mob is still alive. Because service and customer trust are key in this field, believe de loss little time but indirectly you've put an invaluable promotion.
2. If possible, the casing and bateray on hand to customers, to avoid confused over the place, because it is often also the incident of his customers do not recognize bateray if later dropped. Minimal label attached to the inside of the casing and bateray if left, and give mobile service bill with a number corresponding label number.
3. Tidy up your service desk, do not get used to work in a cluttered environment with many mobile jakarta dormant on it. Prepare only what it needs to work at that time.
4. Make sure the damage once again with further checks and stacking strategy handphone jakarta repair or service you would do. So do not rush heats az component let alone unpack. Because there are many tricks jumper or alternative solutions that you can choose. Even worse if steps memblower and unloading components that you do on the basis of trial and error.
5. If hp is not in a state short hence it is better to use a check box cell phone service jakarta to determine the appropriate corrective measures. Most hp damage also come from software problems. And damage to software can be overcome by flashing in full or in part.
6. In exploring hardware damage handphone jakarta do the systematic and sequential, and most importantly use the book in every step of the checking line. If you do a sequential and systematic way then you will find a damaged component appropriately and minimize mistakes.
7. Prepare yourself ... that is the most important
good luck,,,
Subscribe to:
Posts (Atom)